The valve is designed as a 3/2-way changeover valve. In the neutral position, connection P is connected to connection A~ when energized, connection P is connected to connection B. The control magnet can be supplied for different operating voltages. Small internal leaks are permitted because the valve is designed as a slide valve. A magnetic plug (FAIE No. 28483) can optionally be supplied. The valve can be used in all common hydraulic systems. Technical data: max. operating pressure: 250 bar max. return pressure: 10 bar< br> Nominal flow: 40 l/min Tightening torque: 78 Nm Coverage: positive Connections: G3/8 Weight: 2.46 kg Dimensions: 162.5x46x65 mm Operating fluid: Hydraulic oil according to DIN 51524 Viscosity: 10-200 Operating temperature: -20 to +80C

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The consumer connections A and B are located at the top and bottom of the housing. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The operating lever is included in delivery.Case-IHC: 844S, 846, 946, 1046, 1146, 1246, 743XL-856XL, 955XL-1055XL.Eicher:< /strong> King TigerFendt: 102, 103, 104, 105, 106, 108, 200S, 300, 304, 305, 306, 307, 308, 309, 310, 311, 312, 395GTA, 600, 610, 611, 612, 614, 615. Kramer: all models. Lindner: with Steyr transmission. MB-Trac: all models. Schlter: all models. Steyr: Anniversary series with control hydraulics, Plus series, Series 80.Switchable from single-acting to double-acting ~Hydraulic limit switch in lifting ~< br>Locked floating position as fourth switching position after lowering

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The consumer connections A and B are located at the top and bottom of the housing. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The operating lever is included in the scope of delivery.Deutz: All types built up to 1984, DX85, DX90, DX110, DX120, DX145 until the switch to large glass doors.Connection thread:< /strong> M18x1.5mm internal thread ~Switchable from single-acting to double-acting ~Hydraulic limit switch in lifting ~Locked floating position as fourth switching position after lowering

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The consumer connections A and B are located at the top and bottom of the housing. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation.Deutz: 07C series, DX3.10-DX4.70, Agro Prima 4.31-6.17, Agro Xtra 3.57-6.07, Star Cab Series, DX90-145 with large glass door.Switchable from single-acting to double-acting ~Hydraulic limit switch in raising ~Locked floating position as fourth switching position after lowering

This control valve is a /4-way valve that is operated manually to control single-acting and double-acting cylinders as well as hydraulic motors. The control valve from AK- Regeltechnik was developed specifically for Fiatagri tractors with Kontak hydraulics. Due to the high liter output, up to 4 control valves can be flanged directly. Since the hole pattern is completely identical to Kontak/Parker, this valve can also be installed with original Kontak/Parker control valves. The valve is a four-position device. It can be converted from double-acting to single-acting and vice versa. The control valve is a slide-sealed valve that exhibits absolutely neutral fine control behavior and allows extremely low fit leakage even at higher pressures. The device has a locked safety limit switch in the LIFTING position. If you switch further via the LOWER position, you will reach a locked floating position. This can be returned to the NEUTRAL position manually at any time.

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The valve can be mounted on the left or right using a freely positionable sealing plate. The sealing plate is included in delivery.Bosch: 0 521 609 001, 0 521 609 005, 0 521 609 009, 0 521 609 013, 0 521 609 015, 0 521 609 019, 0 521 609 021, 0 521 609 022, 0 521 609 053, 0 521 609 054, 0 521 609 062, 0 521 609 063, 0 521 609 064.0 521 609 074, 0 521 609 098. Case-IHC: 743XL-844XL, 585XL (BJ 87/88), 1055XL, 1255XL, 856XL, 956XL-1056XL, 1256XL(A)-1455XL(A), CS48-CS150, 3220, 4210, 4220, 4230, 4240. Deutz: Agro Star 4.61-6.81, Agro Tron 4.70-4.95, 6.00, 6.05, 6.15, 6.20, 6.30. Fastrac: 135, 155, 185, 525, 1115. JCB Fastrac: 130, 135, 150, 155, 185, 1115, 1135, 2115.Lindner: Geo Trac. Massey-Ferguson: 3000 series. Steyr: 900, 9000 series. Valmet: 6000, 6200 , 6300, 6400, 8000, 8100, 8200, 8300, 8400. Zetor: 3320-3341, 4320-4340, 5320-5341, 6320-6341, 7320-7540, 8520-18345 . ~Switchable from single-acting to double-acting ~Hydraulic limit switch in lifting ~Locked floating position as fourth switching position after lowering

This connection plate is fitted as a replacement for the gearbox cover. The plate has 4 hydraulic connections on the top for P=pump, R=return, W=pressure transfer and Z=additional lift cylinder. This plate makes it possible to connect an externally mounted control unit. If no control valve with pressure transfer line is used, the W connection is closed. In order to guarantee the function of the tractor hydraulics with this installation, a shut-off-valve is fitted in the pressure line between connection P and the control valve. This must be closed when the three-point hydraulic system is used. This prevents pressure from escaping via the tank line of the additionally installed control valve.If a mobile control valve with pressure transfer line is used, connection W is connected to the pressure transfer line connection on the mobile control valve. This allows the tractor hydraulics and the mobile control valve to be used simultaneously. No shut-off-valve is required!Can be used in hydraulic systems of Ford tractor systems 3000, 4000, 5000.Max. Operating pressure: 250 barNominal flow rate 70 l/minTightening torque 78 Nm Connections M18x1.5 Dimensions (LxWxH): 160 x 130 x 20 mm

This main control unit is used in the tractor to control and regulate the hitch. With the control valve, attachments attached to the hoist can be raised and lowered continuously. The position control keeps a position (height of the attachment) preselected on the control lever constant. The traction control allows optimal use of the tractor's performance. Depending on the type of application, the control valve can also be used for mixed control of position and tension control. The control system constantly corrects disturbances automatically, making tractor driving much easier. The valve is very extensively equipped with additional connections for R and P, as well as continuous adjustment of P.The control unit is equipped with a lowering throttle, with which the lowering speed of the hoist can be adjusted.A sealing plug is included in the scope of delivery must be used in the valve if there are only 2 hydraulic connections on the hydraulic flange surface. The non-existent connection must be closed with the plug on the control valve. The sealing plug is held in its position by being flanged to the power lift.There is an additional connection for the return line at the front of the switch cap.Not an original replacement part!

Lever set for Deutz DX series from year of manufacture. 1984 to operate the AK control technology additional control devices.