Hydraulic program

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The consumer connections A and B are located at the top and bottom of the housing. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The operating lever is included in delivery.Case-IHC: 844S, 846, 946, 1046, 1146, 1246, 743XL-856XL, 955XL-1055XL.Eicher:< /strong> King TigerFendt: 102, 103, 104, 105, 106, 108, 200S, 300, 304, 305, 306, 307, 308, 309, 310, 311, 312, 395GTA, 600, 610, 611, 612, 614, 615. Kramer: all models. Lindner: with Steyr transmission. MB-Trac: all models. Schlter: all models. Steyr: Anniversary series with control hydraulics, Plus series, Series 80.Switchable from single-acting to double-acting ~Hydraulic limit switch in lifting ~< br>Locked floating position as fourth switching position after lowering

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The consumer connections A and B are located at the top and bottom of the housing. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The operating lever is included in the scope of delivery.Deutz: All types built up to 1984, DX85, DX90, DX110, DX120, DX145 until the switch to large glass doors.Connection thread:< /strong> M18x1.5mm internal thread ~Switchable from single-acting to double-acting ~Hydraulic limit switch in lifting ~Locked floating position as fourth switching position after lowering

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. It has slide-sealed cylinder ports A and B. This means that extremely low leakage is permitted at high loads. The consumer connections A and B are located at the top and bottom of the housing. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation.Deutz: 07C series, DX3.10-DX4.70, Agro Prima 4.31-6.17, Agro Xtra 3.57-6.07, Star Cab Series, DX90-145 with large glass door.Switchable from single-acting to double-acting ~Hydraulic limit switch in raising ~Locked floating position as fourth switching position after lowering

The version is a mobile control block with 2 additional control devices, a switching valve from the original hydraulics to the additional control device and an operating lever for the three-point hydraulics via the additional control device. Installation is carried out using a mounting plate on the hydraulic riser pipe. The two additional control devices can be used double-acting. The outer control spool can be switched from single-acting to double-acting.The functions of the additional control valve are:Lever No. 1, Switching valve from original hydraulics to additional control unit Lever up: normal tractor hydraulic Lever down: work control valveLever No. 2, actuation of the three-point hydraulics without control hydraulics when switching to the additional control unit with lever No. 1, position downLever No. 3, double-acting control deviceLever No. 4, double-acting control device can be switched to single-acting via the changeover tap on the side of the end plate. If the changeover tap is screwed onto the seat, the control slide can be used double-acting. If the changeover cock is turned out to the stop, the function of the control slide is switched to single-acting.The operating lever of the tractor hydraulics/power lift must be in the outer hydraulics position so that the function of the additional control unit is guaranteed. The scope of delivery includes:The screws for attaching to the hydraulic block are included. ~There is also a hose package with 4 hydraulic hoses and matching hollow screws, ~ 4 pieces of clutch sleeves with dust protection and a holder for the clutch sleeves for attaching to the differential housing included. ~

This control valve is a /4-way valve that is operated manually to control single-acting and double-acting cylinders as well as hydraulic motors. The control valve from AK- Regeltechnik was developed specifically for Fiatagri tractors with Kontak hydraulics. Due to the high liter output, up to 4 control valves can be flanged directly. Since the hole pattern is completely identical to Kontak/Parker, this valve can also be installed with original Kontak/Parker control valves. The valve is a four-position device. It can be converted from double-acting to single-acting and vice versa. The control valve is a slide-sealed valve that exhibits absolutely neutral fine control behavior and allows extremely low fit leakage even at higher pressures. The device has a locked safety limit switch in the LIFTING position. If you switch further via the LOWER position, you will reach a locked floating position. This can be returned to the NEUTRAL position manually at any time.

The additional control device is a 5/4-way valve, which is operated manually to control hydraulic consumers. It is a four-position control device that can be used for double and single-acting lifting cylinders. The device has a grid position in the lifting position, which is equipped with a hydraulic-automatic limit switch. If you switch further via the lowering position, the locked floating position is switched on, which is not unlocked hydraulically (consumer connections A and B connected to each other for the return). The floating position can be used as a locked lowering position for both double-acting and single-acting lifting cylinders. The additional control unit can be switched from double-acting to single-acting during operation. The valve can be mounted on the left or right using a freely positionable sealing plate. The sealing plate is included in delivery.Bosch: 0 521 609 001, 0 521 609 005, 0 521 609 009, 0 521 609 013, 0 521 609 015, 0 521 609 019, 0 521 609 021, 0 521 609 022, 0 521 609 053, 0 521 609 054, 0 521 609 062, 0 521 609 063, 0 521 609 064.0 521 609 074, 0 521 609 098. Case-IHC: 743XL-844XL, 585XL (BJ 87/88), 1055XL, 1255XL, 856XL, 956XL-1056XL, 1256XL(A)-1455XL(A), CS48-CS150, 3220, 4210, 4220, 4230, 4240. Deutz: Agro Star 4.61-6.81, Agro Tron 4.70-4.95, 6.00, 6.05, 6.15, 6.20, 6.30. Fastrac: 135, 155, 185, 525, 1115. JCB Fastrac: 130, 135, 150, 155, 185, 1115, 1135, 2115.Lindner: Geo Trac. Massey-Ferguson: 3000 series. Steyr: 900, 9000 series. Valmet: 6000, 6200 , 6300, 6400, 8000, 8100, 8200, 8300, 8400. Zetor: 3320-3341, 4320-4340, 5320-5341, 6320-6341, 7320-7540, 8520-18345 . ~Switchable from single-acting to double-acting ~Hydraulic limit switch in lifting ~Locked floating position as fourth switching position after lowering

Electronic operating hours counter for machines with PTO drive or rotating parts. The RotoCounter is particularly suitable for shared and rental machines to check and bill the operating hours incurred during use. The measurement is activated via the external sensor. The sensor works without a magnet, but requires elevations or depressions that rotate past the inductive sensor. The AGRETO RotoCounter operating hours counter can be mounted in any position and is completely tamper-proof thanks to a mounting plate with lock.The 6-digit display is in hours and minutes on a permanently switched on LCD display. Dust and waterproof according to protection class IP68 and insensitive to oil and dirt.Scope of delivery: Operating hours counter, sensor with 2m cable, mounting plate with lock and screws, operating instructions.

The angular gear 1018 is a compact and lightweight gear designed for use in circular saws. The gearbox has a gear ratio of 1:2.78, which means that the speed at the output of the gearbox is 2.78 times higher than the speed at the input. The direction of rotation of the output shaft is consistent with the direction of rotation of the input shaft (viewed from the visible end of the shaft). The angle gearbox is equipped with a high-strength aluminum housing, a PTO shaft profile 1 3/8 x 6 at the input and an output shaft with a diameter of 25 mm. The gearbox can accommodate torque peaks of up to 2 times the rated torque. of the nominal torque. ~We would like to point out that an overload protection device must be used in accordance with the performance data of the gearbox. Please note that before putting the gearbox into operation, fill and check the oil level. The maximum power transmission is 7kW at 540rpm and 11kW at 1000rpm. Compact and light High-quality workmanship High torque Long service life Universal applications< /li>

The angular gear 1018 is a compact and lightweight gear designed for use in circular saws. The gearbox has a gear ratio of 1:2.78, which means that the speed at the output of the gearbox is 2.78 times higher than the speed at the input. The direction of rotation of the output shaft is opposite to the direction of rotation of the input shaft (viewed from the visible end of the shaft). The angle gearbox is equipped with a high-strength aluminum housing, a PTO shaft profile 1 3/8 x 6 at the input and an output shaft with a diameter of 25 mm. The gearbox can accommodate torque peaks of up to 2 times the rated torque. We would like to point out that an overload protection device must be used in accordance with the performance data of the gearbox. Attention, fill and check the oil level before putting the gearbox into operation.  ~The maximum power transmission is 7kW at 540rpm and 11kW at 1000rpm.Compact and light< li>High-quality workmanshipHigh torqueLong service lifeUniversal applications

The angular gear 1020 is a compact and lightweight gear designed for use in circular saws. The gearbox has a gear ratio of 1:2.78, which means that the speed at the output of the gearbox is 2.78 times higher than the speed at the input. The direction of rotation of the output shaft is consistent with the direction of rotation of the input shaft (viewed from the visible end of the shaft). The angle gearbox is equipped with a high-strength aluminum housing, a PTO shaft profile 1 3/8 x 6 at the input and an output shaft with a diameter of 25 mm. The gearbox can accommodate torque peaks of up to 2 times the rated torque. of the nominal torque. ~We would like to point out that an overload protection device must be used in accordance with the performance data of the gearbox. Please note that before putting the gearbox into operation, fill and check the oil level. ~ ~The maximum power transmission is 9kW at 540rpm and 13kW at 1000rpm. Compact and light High-quality workmanship High torque Long service life Universal applications < /ul>

The angular gear 1020 is a compact and lightweight gear designed for use in circular saws. The gearbox has a gear ratio of 1:2.78, which means that the speed at the output of the gearbox is 2.78 times higher than the speed at the input. The direction of rotation of the output shaft is opposite to the direction of rotation of the input shaft (viewed from the visible end of the shaft). The angle gearbox is equipped with a high-strength aluminum housing, a PTO shaft profile 1 3/8 x 6 at the input and an output shaft with a diameter of 25 mm. The gearbox can accommodate torque peaks of up to 2 times the rated torque. of the nominal torque. ~We would like to point out that an overload protection device must be used in accordance with the performance data of the gearbox. Attention, fill and check the oil level before putting the gearbox into operation. ~ ~ The maximum power transmission is 9kW at 540rpm and 13kW at 1000rpm.Compact and lightweightHigh-quality workmanshipHigh torqueLong service lifeUniversal applications

The 2020 angular gearbox is a compact gearbox designed for heavy-duty use. The gearbox has a transmission ratio of 1:2.78, which means that the speed at the output of the gearbox is 2.78 times higher than the speed at the input. The direction of rotation of the output shaft is reversed or the same as the direction of rotation of the input shaft (looking at the visible shaft end). The angular gearbox is equipped with a robust cast housing, a 1 3/8 x 6 PTO profile at the input and an output shaft with a diameter of 25 mm (order no. 65792) and 30 mm (order no. 59917). The gearbox can absorb torque peaks of up to 2 times the nominal torque. We would like to point out that an overload protection device must be used in accordance with the performance data of the gearbox.  The maximum power transmission is 9kW at 540rpm and 14kW at 1000rpm.Compact and robustHigh-quality workmanshipHigh torqueLong service lifeUniversal applications

Maximum power transmission for professionals: Bondioli & Pavesi S2050 gearboxesWhen it comes to absolute reliability in continuous operation, farmers and machine builders worldwide rely on drive technology from Bondioli & Pavesi. With the S2050 series right-angle gearboxes, you get robust solutions made of high-quality grey cast iron, specially developed for the toughest mechanical requirements.Why the S2050 series?These gearboxes form the backbone of many agricultural machines – from feed mixers to soil cultivation equipment. They impress with:Maximum load capacity: Thanks to their solid grey cast iron housings, these models offer outstanding stability and vibration damping.Precise performance: The S2050 is the all-rounder for medium loads with an input power of up to 37 kW (50 hp) at 540 rpm.Versatile gear ratios: With common gear ratios (e.g. 1.91:1 or 1:1), the gearboxes can be precisely adapted to your machine requirements.Durability through quality: Developed to the highest industry standards for minimal maintenance intervals and maximum service life.Technical highlights at a glance, transmission ratio 1:1,46Max. power (540 rpm)        approx. 37 kW / 50 hpMax. output torque    up to 446 Nm (at 540 rpm)Material                    High-quality grey cast ironApplication                Fertiliser spreaders, small mowersEnsure original quality for your drive!Whether as original equipment or as a durable spare part, with Bondioli & Pavesi you are choosing efficiency and safety in the field.

3-hole mounting flange with O-ring and screws.

4-hole mounting flange with O-ring and screws.

Piston rod 90 mm, internal thread M36x4, bore bolt 30.2 mm, connection R1/2?IG.For subsequent installation or for cost-effective repairs. These articulated cylinders are installed using the spindle halves already present in the loading wagon.

For subsequent installation or for cost-effective repairs. These articulated cylinders are installed with the spindle halves already present in the loading wagon.Piston rod 60 mm, internal thread M24x3, bore bolt 25.25 mm, connection M14x1.5 ITPlease note when ordering the design of the cylinders in left and right!The photo shows an articulated drawbar cylinder on the left.

Aluminum oil air cooler in panel construction. Max. operating pressure 26 bar, protection class IP44.Application: hay cranes, stationary small units

Aluminum oil air cooler in panel construction. Maximum operating pressure 26 bar, protection class IP68.Oil coolers are used in continuous operation of hydraulic systems to cool the hydraulic oil. However, oil coolers are primarily installed on systems that have been subsequently equipped with additional hydraulic consumers. In many cases, the tank contents are not increased during these conversion work and this increases the circulation and temperature of the oil in the hydraulic system. The optimal operating temperature of a hydraulic system is between 50-60C. If the temperature increases too much, the excess heat must be dissipated via an oil/air cooler.In order to determine the size of the oil cooler, we need some data from you for the calculation:- Gear pump or control pump- Pump delivery rate in L/min- Tank capacity in L (if known)- Oil pressure in the hydraulic system in bar- Ambient temperature in C- Oil temperature of the hydraulic system in C - Connection voltage in VWe will be happy to calculate the oil cooler you need and look forward to your inquiry.

Aluminum oil air cooler in panel construction. Maximum operating pressure 26 bar, protection class IP68.Oil coolers are used in continuous operation of hydraulic systems to cool the hydraulic oil. However, oil coolers are primarily installed on systems that have been subsequently equipped with additional hydraulic consumers. In many cases, the tank contents are not increased during these conversion work and this increases the circulation and temperature of the oil in the hydraulic system. The optimal operating temperature of a hydraulic system is between 50-60C. If the temperature increases too much, the excess heat must be dissipated via an oil/air cooler.In order to determine the size of the oil cooler, we need some data from you for the calculation:- Gear pump or control pump- Pump delivery rate in L/min- Tank capacity in L (if known)- Oil pressure in the hydraulic system in bar- Ambient temperature in C- Oil temperature of the hydraulic system in C - Connection voltage in VWe will be happy to calculate the oil cooler you need and look forward to your inquiry.