Harvest & storage

Practical honey extractor for hobby beekeepers and beginners with electric drive. The drum is made of acid-resistant stainless steel. The basket consists of 8 and 6 mm thick stainless steel rods. The transparent design of the lid makes it possible to observe the spinning process without opening it.With the radial centrifuges, more frames can be centrifuged at the same time than with comparable tangential centrifuges and without turning, which saves time! However, caution is advised with viscous honeys and large frames, as comb breakage could occur more easily.Ø: 720mm18 frames Zander, Langstroth, DNM30 frames Dadant ½ (145 or 160mm height)Drive: electric 230VMotor: 12V/150WDrum material thickness: 0.6mmLid: 4mm thick plexiglassPinch tap: stainless steel 6/4″Bridge, legs: powder-coated

Hobbock made of food-safe plastic (PP) for storing food. Ideal for use as a honey bucket.

Helpful holder for single sieve. This holder has an internal diameter of 23cm. It is suitable for the most common buckets up to an upper outer diameter of approx. 42cm.Finish: Stainless steelWire diameter: 5mm

Fully automatic honey extractor for beginners and advanced beekeepers with 7 preset automatic programs. The slingshot offers space for 6 frames. Depending on the size of the frames, there are cassettes of different sizes. It offers the possibility to work in both manual and automatic mode. Battery operation (12V) allows honey to be extracted anywhere where there is no access to the 230-volt network. The drum is made of acid-resistant stainless steel. The basket is made of rust-proof, acid-resistant rods and is equipped with cassettes. The cassettes are connected to each other with special guides and springs, which allow them to return to the starting position. The safety lock attached to the lid of the honey extractor stops the extractor from operating if the lid is opened during the extractor. The transparent design makes it possible to observe the spinning process without opening it.: 800mm6 framesDimensions cassettes: 440x250mmDrive: electric ground drivePower supply: 12/230VMotor: 24V/350WDrum material thickness: 0.6mm< li>Lid material thickness: 4mmPinch tap: stainless steel 6/4?Bridge, legs: powder-coatedCassettes: stainless steelDelivery : on pallet

Fully automatic honey extractor for beginners and advanced beekeepers with 7 preset automatic programs. The slingshot offers space for 4 frames. Depending on the size of the frames, there are cassettes of different sizes. It offers the possibility to work in both manual and automatic mode. Battery operation (12V) allows honey to be extracted anywhere where there is no access to the 230-volt network. The drum is made of acid-resistant stainless steel. The basket is made of rust-proof, acid-resistant rods and is equipped with cassettes. The cassettes are connected to each other with special guides and springs, which allow them to return to the starting position. The safety lock attached to the lid of the honey extractor stops the extractor from operating if the lid is opened during the extractor. The transparent design makes it possible to observe the spinning process without opening it.Ø: 720mm4 framesDrive: electric floor drivePower supply: 12/230VMotor: 24V/250WDrum material thickness: 0.6mmLid material thickness: 4mmHoney gate: stainless steel 6/4 ZollBridge, legs: powder-coatedCassettes: stainless steelDelivery: on palletRequired Door width: 750mm

Single sieve made entirely of stainless steel with a diameter of 22.5 cm.  Ideally suited as a pre-screen for filtering coarser particles.Strainer holder as optional accessory - please order separately!

The bucket holder made of stainless steel can be hung in any standard honey container.Extra wide design for perfect support of the bucket. The cut edges have been chamfered to protect your devices from damage.

Metal stand for different types of honey filling pots.The version for 30/50kg is designed without the lower crossbars.

Inexpensive narrow honey extractor with manual drive and plastic squeeze tap. Designed for use in smaller apiaries in the hobby sector. The extractor has space for 3 frames (DNM, Zander, Langstroth). The drum is made of acid-resistant stainless steel. The basket is made of stainless, acid-resistant rods. The transparent design of the lid makes it possible to observe the spinning process without opening it.Ø: 400mm3 frames (DNM, Zander, LS)Drive: manual/hand driveDrum material thickness: 0.6mmPinch tap: plastic 6/4″Bridge, legs: powder-coatedOverall dimensions (L x W x H): 640 x 570 x 1080 mm

Inexpensive honey extractor for hobby beekeepers and beginners with hand drive. The slingshot offers space for 4 frames (DNM, Zander, LS, BW, Dadant). The drum is made of acid-resistant stainless steel. The basket is made of rust-proof, acid-resistant rods. Thanks to the ingenious design without a central axis, the frames can be turned in the spinner without having to put them out and back in again. The transparent design of the lid makes it possible to observe the spinning process without opening it.:600mm4 frames (DNM, Zander, LS, BW, Dadant, EHM)Drive: manual/hand driveDrum material thickness: 0.6mmPinch tap: stainless steel 6/4?Bridge, legs: powder-coated< /li>

Practical honey extractor for hobby beekeepers and beginners with an electric drive. The slingshot offers space for 4 frames (DNM, Zander, LS, BW, Dadant). The drum is made of acid-resistant stainless steel. The basket is made of rust-proof, acid-resistant rods. The basket can be easily removed for cleaning. Thanks to the ingenious design without a central axis, the frames can be turned in the spinner without having to put them out and back in again. The transparent design of the lid makes it possible to observe the spinning process without opening it.:600mm4 frames (DNM, Zander, LS, BW, Dadant, EHM) Drive: electric Power supply: 230V Motor: 120W Drum material thickness: 0.6mm Pinch tap: stainless steel 6/4?Bridge, legs: powder coated

Tripod for pointed screens with a diameter of at least 35cm.

Uncapping tray with a rust-free stainless steel sieve insert, which is easy to clean.Inner tray: stainless steel sieve with inner dimensions: 34.5cm x 55cm x 7cmDimensions of the uncapping tray: 41 x 61cm, Height 10cmEasy to disassemble and cleanIn the set: uncapping tray, sieve, universal stand for frames (for all frame sizes)The color of the plastic tray may vary.

Uncapping dishes consisting of a stainless steel cup (45x29x3.5cm) and frame. The practical design of the frame means that both sides can be used, with one side used for unlidding and the other as a shelf. Alternatively it would also be suitable for 2 people.

Uncapping tray with a plastic sieve insert, which is easy to clean.Inner tray: plastic sieve with inner dimensions: 34.5cm x 55cm x 7cmDimensions of the uncapping tray: 41 x 61cm, height 20cmeasy to disassemble and cleanin the set: uncapping tray, sieve, universal stand for frames (for all frame sizes)The color of the plastic tray may vary.

Uncapping fork with curved metal tines and wooden handle

Uncapping fork with curved tines made of stainless steel

Uncapping fork with 21 straight tines made of stainless steel.

Topping knife made of stainless steel with a wooden handle and a smooth blade on both sides.Blade: 280 mm long and approximately 33 mm wide

Stainless steel uncapping knife with wooden handle. The blade has two different sides and can be used on both sides. One side has a smooth finish, the other has a wavy edge.

Electric uncapping knife with 27cm long, heated cutting edge for efficient uncapping of honeycombs.The temperature can be regulated using a built-in thermostat.

Stainless steel slicer with wooden handle for uncapping honeycombs.

Uncapping wax bag made of nylon for separating honey from the cap or frame wax.The bag can be hung in the honey extractor.