Hydraulic motors

Our offer

Multigreifschaufel kompakt mit EURO-Aufnahme

21294

Compact multi-grab shovel with EURO holder

The compact multi-grab shovel for universal use is suitable for loading loose or bulky goods such as manure or shrub cuttings. The screwed side panels prevent load losses. The compact multi-grab bucket is available for tractors, farm loaders and wheel loaders with a Euro mount. Thanks to the high opening width, the edge of the bucket can be moved towards a wall when the gripper is open. Total height 645 mm, blade plate 6 mm thick, including side plates, plug BG3, double scraper edge 500HB

€2,295.00*

-24 %

Kurbellagergehäuse hinten komplett, 281.0090

FA117928

Complete rear crank bearing housing, 281.0090

Rear crank bearing housing for driving the bedknife on Busatis and ESM double knife mowers.

€179.00* €235.00* (23.83% saved)

2549

Cooking tines without a share

Tine material 25x8.

€8.79*

-13 %

FA54554

Crowd loose

Working width 105 mm, suitable for Regent chipper.

€3.49* €3.99* (12.53% saved)

-26 %

FA107995

Cutter head screw M8x1x20

Cutter head screw M8x1x20, strength class 10.9. Suitable for Aebi, BCS and Reform.

€1.69* €2.29* (26.2% saved)

-40 %

FA63556

Double beam blade 2-hole

98x74x3 mm, hole spacing 51 mm

€2.39* €4.00* (40.25% saved)

-5 %

FA2521

Hammer mallet suitable for

Agricom, Agritec, Berti, Breviglieri, MEAAT, Mthing, Oehler, Vigolo, Vogel and Noot, AP-00891

€19.90* €20.90* (4.78% saved)

-10 %

FA2531

Hammer mallet suitable for

Agricom, Becchio &~ Mandrile, Desvoys, Kuhn, Kverneland, Maletti, MEAAT, Nobili, Omarv, Perugini, Rinieri, Vogel and Noot, Zappator

€17.90* €19.90* (10.05% saved)

Injektor-Doppelflachstrahldüse AI3070 TeeJet

72983

Injector double flat jet nozzle AI3070 TeeJet

AI3070 with two wide-angle flat jets, therefore very suitable for lower spray heights for better use of the droplet energy during deposition.30 jet forward in the direction of travel optimizes penetration in the upper leaf and ear area on the front sides, 70 jet towards the rear covers rear target areas.Drop sizes like short AIXR TeeJet and therefore the perfect compromise between loss reduction and degree of coverage. Large, round, free cross-sections for liquid and air increase operational safety and wear.Plastic designInjector can be removed if necessary.Automatic alignment with Quick TeeJet cap and seal Order No. 72989 Pressure range 1.5 - 6 bar, optimal 2 - 5 bar.Typical applications: Ear treatmentsother fungicides and insecticides in grain, leafy crops and special crops, potato cultivationHerbicides, especially for grasses and rough fields .

€13.90*

-31 %

47888

Interchangeable tip S1W

€15.90* €23.00* (30.87% saved)

All Products

Antriebsstummel 1 3/8 x 6 zu RT-Getriebe

FA129257

BERMA Drive stub 1 3/8 x 6 for RT gearbox

In order to drive the RT series gearboxes with a drive shaft, a PTO stub is fitted instead of an oil motor. The PTO stub has a profile of 1 3/8 x 6 and, on the gearbox side, a smooth shaft with a diameter of 25 mm and a keyway.

€169.00*

Vorsatzlager für Ölmotore mit SAE-A Anschluss und Ø 25 mm Welle, Ausgangswelle Ø 32 mm

FA126993

Front bearing for oil engines with SAE-A connection and Ø 25 mm shaft, output shaft Ø 25 mm

Front bearing suitable for all oil motors with a 2-hole SAE-A connection and shaft diameter of 25 mm. These auxiliary bearings are used for higher axial loads on oil motors, e.g. due to a chain drive or V-belt drive. Two tapered roller bearings are installed in the bearing.There is an SAE-A 4-hole flange with a shaft diameter of 25 mm on the output side. The tapered roller bearings are lubricated via a grease nipple on the bearing housing.

€259.00*

FA126994

Front bearing for oil engines with SAE-A connection and Ø 25 mm shaft, output shaft Ø 32 mm

Front bearing suitable for all oil motors with a 2-hole SAE-A connection and shaft diameter of 25 mm. These auxiliary bearings are used for higher axial loads on oil motors, e.g. due to a chain drive or V-belt drive. Two tapered roller bearings are installed in the bearing.There is an SAE-A 4-hole flange with a shaft diameter of 32 mm on the output side. The tapered roller bearings are lubricated via a grease nipple on the bearing housing.

€259.00*

26859

Hydraulic motor MM

Displacement (cm³/rev.): 40 L (mm): 118,5 Power max. cont. (kW): 1,8 Power max. int. (kW): 3,0 Type: MM40 max. int. pressure (bar): 110 max. int. speed (rpm): 625 max. pressure cont. (bar): 80 max. speed cont. (rpm): 500 max. torque cont. (Nm): 41 max. torque int. (Nm): 57

With side connections R 3/8?, shaft 16 mm, max. inlet pressure 140 bar.

€289.00*

Variants from €247.00*

18397

Hydraulic motor MP

Displacement (cm³/rev.): 79,2 L (mm): 140 Power max. cont. (kW): 10,2 Power max. int. (kW): 12,5 Type: MP80 max. int. pressure (bar): 175 max. int. speed (rpm): 945 max. oil flow cont. (l/min): 60 max. oil flow int. (l/min): 70 max. pressure cont. (bar): 140 max. speed cont. (rpm): 755 max. torque cont. (Nm): 151 max. torque int. (Nm): 195

Connections R 1/2?, shaft 25 mm, plain bearing.

€259.00*

18424

Hydraulic motor MR

Displacement (cm³/rev.): 199,8 L (mm): 163,5 Power max. cont. (kW): 11 Power max. int. (kW): 13 Type: MR200 max. int. pressure (bar): 200 max. int. speed (rpm): 375 max. oil flow cont. (l/min): 60 max. oil flow int. (l/min): 75 max. pressure cont. (bar): 175 max. speed cont. (rpm): 300 max. torque cont. (Nm): 450 max. torque int. (Nm): 500

Connections R 1/2?, shaft 32 mm, plain bearing.

€375.00*

Variants from €319.00*

47064

Hydraulic motor RL

Displacement (cm³/rev.): 250,1 L (mm): 187 Power max. cont. (kW): 10 Power max. int. (kW): 12 Type: RL250 max. int. pressure (bar): 200 max. int. speed (rpm): 300 max. oil flow cont. (l/min): 60 max. oil flow int. (l/min): 75 max. pressure cont. (bar): 175 max. speed cont. (rpm): 240 max. torque cont. (Nm): 540 max. torque int. (Nm): 610

With side connections R 1/2?, shaft 25 mm, with tapered roller bearings.

€459.00*

Variants from €299.00*

Befestigungsflansch für Ölmotor Baureihe MM

FA27838

Mounting flange for oil motor series MM

Oval flange for hydraulic motors of the MM series. Delivery includes 3 countersunk screws.

€29.00*

FA37494

Profile sleeve 1 3/8' x 6 internal teeth

For attaching to oil engines. Bore 25 mm, keyway 8mm, outer 49 mm, length 130 mm.

€49.90*

Zapfwellenverlängerung mit Bohrung und Keilnut Profil 1 3/8 x 6

FA9433

PTO stub 1 3/8 x 6"

For attaching to oil engines. Bore diameter 25 mm, keyway 8 mm.

€24.95*

Unser Produktleiter

Werner Meixner

Werner has been with FAIE since 1994. He is our expert for agricultural machinery. If you are ever looking for advice in these areas, you are always in good hands with him.