Hydraulic program

These valves allow an adjustable flow from the consumer to the return. If the flow rate determined by the setting is exceeded, for example in the event of a pipe burst, the valve closes immediately. The movable baffle plate is pressed onto the valve body against the built-in spring due to the increased flow forces. The valves should be installed on the consumer as soon as possible to ensure maximum safety.

Radio control with hydraulic control valve!2-channel radio control set for hydraulically driven winches, oil motors or hydraulic cylinders with 12 volt monoblock valve, the radio is pre-wired with a 7-pin vehicle plug , the solenoid valve is double-acting and has a connection for pressure continuation, technical data: 12 volts 3 amps, flow rate max. 50 L/min. Connections: 1/2?IG inlet/output and consumer<~cbht/>~1/2?AG to continue printing

Pressure force 2261 kg, tensile force 1378 kg at 180 bar, connection G 1/4, nominal pressure 250bar

Pressure force 14137 kg, tensile force 10602 kg at 180 bar, connection G 1/2, nominal pressure 250bar

Bolt d=40 mm, connection G=R1/2", T=69 mm, U=25 mm, pressure force 14137 kg, tensile force 9047 kg at 180 bar, nominal pressure 250 bar.

Pressure force 20357 kg, tensile force 13430 kg at 180 bar, connection G 1/2, nominal pressure 250bar

Bolt d=16 mm, connection G=R1/4", T=35 mm, U=15 mm, pressure force 883 kg, tensile force 521 kg at 180 bar, nominal pressure 250 bar.Joint eye 16 mm with lubrication hole on both sides .

Pressure force 883 kg, tensile force 521 kg at 180 bar, connection G 1/4, nominal pressure 250bar

Pressure force 1447 kg, tensile force 882 kg at 180 bar, connection G 1/4, nominal pressure 250bar

Bolt d=20 mm, connection G=R1/4", T=38 mm, U=22 mm, pressure force 1447 kg, tensile force 882 kg at 180 bar, nominal pressure 250 bar.Joint eye 20 mm on the piston rod side with a lubrication hole .

Bolt d=20 mm, connection G=R1/4", T=38 mm, U=22 mm, pressure force 2261 kg, tensile force 1378 kg at 180 bar, nominal pressure 250 bar.Joint eye 20 mm on the piston rod side with a lubrication hole .

Pressure force 3534 kg, tensile force 2650 kg at 180 bar, connection G 3/8, nominal pressure 250bar

Bolt d=25 mm, connection G=R3/8", T=45 mm, U=22 mm, pressure force 3534 kg, tensile force 2261 kg at 180 bar, nominal pressure 250 bar.

Pressure force 3534 kg, tensile force 2261 kg at 180 bar, connection G 3/8, nominal pressure 250bar

Bolt d=30 mm, connection G=R3/8", T=51 mm, U=23 mm, pressure force 5089 kg, tensile force 2827 kg at 180 bar, nominal pressure 250 bar.

Pressure force 5089 kg, tensile force 2826 kg at 180 bar, connection G 3/8, nominal pressure 250bar

Pressure force 6927 kg, tensile force 4665 kg at 180 bar, connection G 3/8, nominal pressure 250bar

Bolt d=35 mm, connection G=R1/2", T=61 mm, U=25 mm, pressure force 9047 kg, tensile force 5513 kg at 180 bar, nominal pressure 250 bar.

Pressure force 9047 kg, tensile force 5513 kg at 180 bar, connection G 1/2, nominal pressure 250bar

Especially for retrofitting mechanical front loaders with hydraulic actuation of the tools. In conjunction with a EURO quick-change frame, a fully hydraulic front loader can be created in a very short time (see front loader conversion kit Faie No. 70599). With the 895 mm long tilting linkage and the lifting path of 507 mm, a tilt angle of up to 180 can be achieved.The scope of delivery includes 1 hydraulic hose with union nut M18x1.5 / 12L in lengths of 1100 mm and 1300 mm included.Pressure force per cylinder 6927 kg at 180 barTensile force per cylinder 5195 kg at 180 barTilt angle up to 180 Stroke path 507 mm

Hydraulic hand pumps are used in hydraulic systems where only one hydraulic movement is required. These are mostly simple systems where high pressure with low flow rate is required, such as bending tools, lifting devices, tipping devices for car trailers and smaller agricultural trailers, etc. Hand pumps are a simple and inexpensive solution for operating double-acting hydraulic cylinders. The extension and retraction of the hydraulic cylinder is controlled by the integrated 4-3 directional control valve.The hand lever is included.Connection thread: 3/8" BSP internal thread

Hydraulic hand pumps are used in hydraulic systems where only one hydraulic movement is required. These are mostly simple systems where high pressure with low delivery capacity is required, such as bending tools, lifting devices, tipping devices for car trailers and smaller agricultural trailers, etc. Hand pumps are a simple and inexpensive solution for operating single-acting hydraulic cylinders. The hydraulic cylinder is retracted by opening the drain cock and using the weight of the load.The hand lever is included.Connection thread: 3/8" BSP internal thread

For universal use in agriculture and industry. The simple and inexpensive solution for operating hydraulic cylinders.

For universal use in agriculture and industry. The simple and inexpensive solution for operating hydraulic cylinders.