Products

Original ESM friction plate instead of Agria 07506 suitable for finger bars from Agria, ESM and Vogel &~ Noot.

Suitable for Steyr T80-180 with cleaning plates

Suitable for Type 116, 316 center section

0.3 kg Ingredients: onion (49%), vegetable fat, wheat flour, saltUse: in soups, sauces,...

Particularly suitable for drives where there is a larger radial load, e.g. drive via V-belt pulley.Don't forget to order matching drive pinions for the front bearing for the hydraulic pump! You can find these on page 465 at the bottom right.

​Front bearing suitable for all oil motors with a 2-hole SAE-A connection and shaft diameter of 25 mm. These auxiliary bearings are used for higher axial loads on oil motors, e.g. due to a chain drive or V-belt drive. Two tapered roller bearings are installed in the bearing.There is an SAE-A 4-hole flange with a shaft diameter of 25 mm on the output side. The tapered roller bearings are lubricated via a grease nipple on the bearing housing.

Front bearing suitable for all oil motors with a 2-hole SAE-A connection and shaft diameter of 25 mm. These auxiliary bearings are used for higher axial loads on oil motors, e.g. due to a chain drive or V-belt drive. Two tapered roller bearings are installed in the bearing.There is an SAE-A 4-hole flange with a shaft diameter of 32 mm on the output side. The tapered roller bearings are lubricated via a grease nipple on the bearing housing.

Front crank bearing housing for driving the upper blade on Busatis and ESM double-blade mowers.

Dimension: 56x76x9mm

Galvanized door element suitable for modular calf pens

Length: 148mm

?The harrow tine is mounted on the seed harrow at the front, viewed in the direction of travel.

LxWxH: 120x80x56 mm, hole spacing 58 mm, suitable for e.g. Case IH, Deutz, Fiat, Ford, John Deere, MF, ...right/left

LxWxH: 120x80x135 mm, 22 slanted mounting plate, suitable for e.g. Case IH, Deutz, Fiat, Ford, John Deere, MF, ... right/left

LxWxH: 85x85x50 mm, M4 screws, hole spacing 45 mm, suitable for e.g. Case IH, John Deere, Fendt, MF, New Holland, ...right/left

suitable for MF, LxWxH: 128x68x48mm, ~Fastening: 2 screws M6, hole spacing: 45mm ?Design: left/right

Fender flares primed, front left for Steyr 8065-8095Width version 220mm

Ausführung: vorne linksBreite: 95 mmFarbe:  Rot RAL 3000 

No old iron through the retrofit solution from Faie.Older tractors can often still do valuable work on farms if they are adapted to today's requirements. A simple retrofit solution is to upgrade the mechanical front loader with fully hydraulic device controls. A 1-cylinder version and a version with 2 cylinders are available for this retrofit.If equipment is changed frequently, it makes sense to attach a quick-change frame for coupling and uncoupling the implements with EURONORM. Our complete front loader conversion kit for category 2 front loaders with 85cm and category 3 with 102cm is ideal for this purpose. This consists of a fully hydraulic device actuation in a 2-cylinder design and a quick-change frame with central locking.Pressure force 6927 kg at 180 bar, pulling force 5195 kg at 180 bar, hydraulic hose length 1100 mm and 1300 mm, hydraulic connection M18x1.5 union nut 12L, weight 140kg.

Made of spring steel 55Si8, partly C45. All tines with tapered nut and quality guarantee.

No conical nut necessary.

60.4003.800, double T-profileMade of spring steel 55Si8, partly C45. All tines with tapered nut and quality guarantee.

60.4003.800, star profileMade of spring steel 55Si8, partly C45. All tines with tapered nut and quality guarantee.