Hydraulic program

​For easy retrofitting of a radio control system – NO complicated cable connections! All components are permanently wired and easy to install! 2-channel radio device with wired receiver and transmitter with on/off switch and two functions. The input on the receiver is hard-wired with a 7-pin automotive connector and the outputs with a 3-pin DIN plug each.Frequency: ISM 868 / 915 MHzOutputs max. 5 A,Protection class: IP 67.

​PPlug-ready radio set for 12 and 24 volts!For easy retrofitting of a radio control - NO complicated cable connection!All components are pre-wired and easy to install!2-channel radio set with wired receiver and transmitter with on/off switch and two functions. The 2-pole input on the receiver can be connected to 12 V or 24 V and the outputs each with a 3-pin DIN plug. Frequency: ISM 868 / 915 MHz  Outputs max. 5 A, Protection class: IP 68.

Tractor 2K with union nut on both sides, 2 high-tensile steel wire meshes, thin synthetic top rubber, high flexibility, extremely small bending radius, low weight. max. operating pressure 400 bar, minimum bending radius 45 mm, weight 275 g/m, outer diameter 13.1 mm< br>Applied standards: EN 857 2SC, ISO 11237 2SC, SAE 100 R16S

Tractor 2K with union nut on both sides, 2 high-tensile steel wire meshes, thin synthetic top rubber, high flexibility, extremely small bending radius, low weight. max. operating pressure 350 bar, minimum bending radius 55 mm, weight 330 g/m, outer diameter 14.7 mm< br>Applied standards: EN 857 2SC, ISO 11237 2SC, SAE 100 R16S

Tractor 2K with union nut on both sides, 2 high-tensile steel wire meshes, thin synthetic top rubber, high flexibility, extremely small bending radius, low weight. max. operating pressure 350 bar, minimum bending radius 55 mm, weight 330 g/m, outer diameter 14.7 mm< br>Applied standards: EN 857 2SC, ISO 11237 2SC, SAE 100 R16S

Tractor 2K with union nut M18x1.5 on both sides, tube 12L, 1 straight connection, 1 connection 90 bent, 2 high-tensile steel wire meshes, thin synthetic top rubber, high flexibility, extremely small bending radius, low weight.max. Operating pressure 330 bar, minimum bending radius 65 mm, weight 395 g/m, connection 12L, M18x1.5 mmApplied standards: EN 857 2SC, ISO 11237 2SC, SAE 100 R16S

Tractor 2K with union nut M18x1.5 on both sides, tube 12L, 2 high-tensile steel wire meshes, thin synthetic top rubber, high flexibility, extremely small bending radius, low weight.max. Operating pressure 330 bar, minimum bending radius 65 mm, weight 395 g/m, outer diameter 16.8 mm Applied standards: EN 857 2SC, ISO 11237 2SC, SAE 100 R16S

Tractor 2K with union nut M22x1.5 on both sides, tube 15L, 2 high-tensile steel wire meshes, thin synthetic top rubber, high flexibility, extremely small bending radius, low weight.max. Operating pressure 275 bar, minimum bending radius 80 mm, weight 510 g/m, outer diameter 20.3 mmApplied standards: EN 857 2SC, ISO 11237 2SC, SAE 100 R16S

Tractor 2K with union nut M22x1.5 on both sides, tube 15L, 2 high-tensile steel wire meshes, thin synthetic top rubber, high flexibility, extremely small bending radius, low weight.max. Operating pressure 275 bar, minimum bending radius 80 mm, weight 510 g/m, outer diameter 20.3 mmApplied standards: EN 857 2SC, ISO 11237 2SC, SAE 100 R16S

Tractor 2K with union nut on both sides, 2 high-tensile steel wire meshes, thin synthetic top rubber, high flexibility, extremely small bending radius, low weight. max. operating pressure 400 bar, minimum bending radius 45 mm, weight 275 g/m, outer diameter 13.1 mm< br>Applied standards: EN 857 2SC, ISO 11237 2SC, SAE 100 R16S

Particularly suitable for attachment to the front PTO shaft to change the direction of rotation and reduce the speed from 1000 rpm to 526 rpm. The transmission is mounted on the tractor side.Input Y:PTO shaft stub or internal toothing540/1000 rpm, 26.4/51.5 kW, 477/928 NmConnection 1 3/8x6, internal or external toothingPossibility with through drive 1:1 (direction of rotation constant).Output X:284/ 526 rpm, 482/895 NmConnection 1 3/8x6 external toothingReversal of direction of rotationIn general, torque peaks up to 2 times the nominal torque do not cause any damage to the individual gear components. However, complete integrity can only be guaranteed by a suitable safety device.

Especially suitable for the front PTO to change the direction of rotation and reduce the speed from 1000 rpm to 526 rpm. The gearbox is installed on the device side.Input Y:540/1000 rpm26.4/39.7 kW 477/386 NmConnection 1 3/8x6Output X:284/526 rpm895/725 NmConnection 1 3/8x6 inner profile Reversal of direction of rotationPossibility with through drive 1:1 (direction of rotation remains the same). In general, torque peaks of up to 2 times the nominal torque do not cause any damage to the individual gear components. However, complete integrity can only be guaranteed by a suitable safety device.

​The 95000 series reduction gearbox is a compact gearbox designed for use with hydraulic motors. The gearbox has a reduction ratio of 2:1, which means that the speed at the output of the gearbox is 2 times slower than the speed at the input. The direction of rotation of the output shaft is the reverse of the direction of rotation of the input shaft (viewed at the visible shaft end). The gearbox is equipped with a robust aluminium housing. The input side has a bore with a diameter of 25 mm and a keyway of 8 mm. The connecting flange is suitable for oil motors with an SAE-A flange.The output side is a hollow shaft with a diameter of 35 mm and a keyway of 10 mm. Four M10 holes with a bolt circle diameter of 110 mm are arranged on the output side for fastening the gearbox. Please fill up and check the oil level before commissioning the gearbox. The maximum power transmission is 10 kW.Compact and robust High-quality workmanship High torque Long service life Universal application possibilities

​The 96071 series reduction gearbox is a compact gearbox designed for use with hydraulic motors. The gearbox has a reduction ratio of 3:1, which means that the speed at the output of the gearbox is 3 times slower than the speed at the input. The direction of rotation of the output shaft is the reverse of the direction of rotation of the input shaft (viewed at the visible shaft end). The gearbox is equipped with a robust aluminium housing. The input side has a bore with a diameter of 25 mm and a keyway of 8 mm. The connecting flange is suitable for oil motors with an SAE-A flange.The output side is a hollow shaft with a diameter of 35 mm and a keyway of 10 mm. Four M12 holes with a bolt circle diameter of 110 mm are arranged on the output side for fastening the gearbox. Please fill up and check the oil level before commissioning the gearbox. The maximum power transmission is 20 kW.Compact and robust High-quality workmanship High torque Long service life Universal application possibilities

Standard filtration 25 micron, with by-pass valve, 1.7 bar

Standard filtration 10 micron, with by-pass valve, 1.7 bar

Connection input (y): 1-3/8x6 (inner profile)~Connection output (x): 1-3/8x6~ Reversal of direction of rotation

Technical data: 22 kW, 540 rpm, 395 Nm Input connection: 1-3/8x6 (inner profile) Output connection: 1-3/8x6 1. Output shaft: direction of rotation remains the same 2nd output shaft: reversal of direction of rotationIn general, torque peaks of up to 2 times the nominal torque do not cause any damage to the individual gear components. However, complete integrity can only be guaranteed by a suitable safety device.

Reversing or reversing gear to change the direction of rotation with through drive.Input Y:540 rpmPower: 51.5 kWTorque: 910 Nm Connection 1 3/8x6Reversal of direction of rotationPossibility with through drive 1:1 (direction of rotation remains the same).In general, torque peaks up to 2 times the nominal torque do not lead to any damage to the individual gear components. However, complete integrity can only be guaranteed by a suitable safety device.

with pipe connection, light series DIN 2353, max. operating pressure 230bar