Hydraulic program

Rod head for hydraulic top link. Installation length 63mm, width 50mm

With fork and thread M6, adjustment thread M16x1.5mm, bending radius 200 mm.

70 shore. The length of the round cord is 2 m in the following diameters: 1.78 - 2 - 2.4 - 2.62 - 3 - 3.5 - 4 - 5 - 5.33 - 5.7 - 6 - 7 -8 mm . Incl. cutter knife, roll meter 3 m, glue and cutting gauge.

In agricultural technology, scraper floors are often driven with a hydraulic drive via an oil motor in conjunction with a scraper floor gear. These drives can be found in loading wagons, manure spreaders and also in chopping wagons. For this purpose, gearboxes with a high reduction ratio and a high transferable torque are used. The gearboxes are supplied with different diameters for the drive shaft. A hydraulic motor with a shaft diameter of 25 mm and an SAE-A flange is used on the input side. The design of the hydraulic motor depends on the required speed of the scraper floor shaft and the available liter output of the hydraulic pump. In general, torque peaks of up to 2 times the nominal torque do not cause any damage to the individual gear components. However, complete integrity can only be guaranteed by a suitable safety device.

Rubber cross for the flexible claw couplings from OMT

Spare parts set suitable for FASTER oil collection system.

for all Faster multicouplers

Safety lock for locking the locking lever when the lever is closed and open. The locking mechanism is suitable for all DNP multi-couplers in the PSF series. The set consists of a push button, 1 roller and 1 spring.

​Safety lock for locking the locking lever when the lever is closed and open. The locking mechanism is suitable for all DNP multi-couplers in the PSQ and PSL series. The set consists of a push button, 2 rollers and 2 springs.

for all Faster multi-couplers

In agricultural technology, scraper floors are often driven with a hydraulic drive via an oil motor in conjunction with a scraper floor gear. These drives can be found in loading wagons, manure spreaders and also in chopping wagons. For this purpose, gearboxes with a high reduction ratio and a high transferable torque are used. The gearboxes are supplied with different diameters for the drive shaft. A hydraulic motor with a shaft diameter of 25 mm and an SAE-A flange is used on the input side. The design of the hydraulic motor depends on the required speed of the scraper floor shaft and the available liter output of the hydraulic pump. In general, torque peaks of up to 2 times the nominal torque do not cause any damage to the individual gear components. However, complete integrity can only be guaranteed by a suitable safety device.

The PVV3 screw coupling series from dnp complies with ISO standard 14541 in sizes DN06 to DN20. In the standard version, the couplings are equipped with NBR seals. A version with EPDM or Viton seals is available on request. The operating pressure of the couplings has a range of 300 (DN30) to 450 bar (DN06).Coupling under residual pressure is possible on both the plug side and the socket side !

The PVV3 screw coupling series from dnp complies with ISO standard 14541 in sizes DN06 to DN20. In the standard version, the couplings are equipped with NBR seals. A version with EPDM or Viton seals is available on request. The operating pressure of the couplings has a range of 300 (DN30) to 450 bar (DN06).Coupling under residual pressure is possible on both the plug side and the socket side !

Bulkhead fitting

Bulkhead fitting

According to DIN 2353.

According to DIN 2353.

According to DIN 2353

According to DIN 2353

Consisting of 3 pieces M8x190, 2 pieces M6x120 Allen.

Consisting of 3 pieces M8x180, 2 pieces M6x120 Allen.

for 2 additional control devices, M10x155 mm

Consisting of 3 pieces M8x240, 2 pieces M6x170 Allen.

for 3 additional control devices M10x195 mm