Products

​Wire mesh live trap with a two-sided snap or trap door,ideal for safely and humanely catching animals such as foxes, stray cats, raccoons, martens, and other animals.The sturdy metal mesh allows you to see directly into your trap without endangering yourself or the trapped animal.Wooden handle for safe transport, easy preparation and attachment of the bait with helpful accessories (metal tongs, egg holder, meat skewer).Pre-assembled and ready for immediate use. Central door for easy bait placement.Wire thickness: 3.3 mm.Wire mesh: 38 x 38 mm.Weight: 9.7 kg. L x W x H: 120 x 33 x 42 cm.FAIR TIP: When used as a marten trap, we recommend darkening the trap and lining the wire mesh floor with leaves!Please observe the regional hunting regulations regarding live hunting!

Occurrence: various boxwood species Main symptoms: eaten leaves, light beige in color light green feces crumbs in the web and under the plant in severe infestation webs clearly visible Biology: The larva spins itself between the leaves and hibernates. In spring, when temperatures rise to over 7C for a longer period of time, the caterpillars start feeding again. They usually go through 6 larval stages during their development into pupae. The females, which live for around 8 days, lay their eggs on the underside of the leaves. Under favorable climatic conditions, the development of a second and third generation per year is possible. Egg laying: female lays approx. 100-150 eggs Caterpillar stage (damage stage): approx. 10 weeks at 15C for approx. 3 weeks 25-30C Lifespan of the butterflies: approx. 8-9 days Flight time of the first generation: mid-March to early April (at dusk) Flight time of the second &~ third generation: until OctoberApplication: Assemble the trap and attach it with the included wire depending on the area of use. (The exact assembly instructions and the area of use are described in detail for each pheromone trap.) In order not to lure the pest directly into the crops to be protected, the trap should be hung in another nearby tree, for example. If this is not possible, the trap can be attached to a stake. Hang the trap between the main wind direction and the tree, at eye level. The trap entrances must not be blocked by branches and leaves. Each trap should be checked at regular intervals of 2-3 days. Whenever the trap is checked, the glue base must be cleaned of adhering insects using an auxiliary instrument (e.g. twig, wooden spatula) if necessary so that the full glue surface is retained. If it is heavily soiled, replace the glue base or re-glue it with Soveurode special glue (spray glue). Replace the attractant stubble and, if necessary, the glue base after 4-8 weeks.The traps must be hung up before the moth begins to fly. A trap set consists of: 1 trap body (WitaTrap Delta Super Trap grp) 2 glue bases (packaged separately) 2 pheromone stubble (packaged separately) Hanging wire for assembly and a precise description.

Suspenders with practical clips, yellow, 35mm, one size.

Foldable, galvanized, hole spacing 30 mm.

for trailer lighting socket

This top link bracket enables hydraulic top links to be securely mounted on the tractor and ensures a stable attachment to the tractor. The robust design makes installation easy and reliably holds the top link in position when it is not in use. Suitable as a practical retrofit or spare part for hydraulic top links. Advantages & Features • Simple, robust mounting for the retaining bracket of a top link. • Tractor-side design – secure and neat mounting. • Robust steel construction – durable and resilient in daily use. • Easy retrofitting – ideal as a replacement or addition to agricultural vehicles. Frequently Asked Questions What is the mount used for? It is used to secure or mount the retaining bracket of a (hydraulic) top link on the tractor side. Is the bracket suitable for retrofitting? Yes, it is suitable as a spare part or for retrofitting compatible tractors. Is a top link bracket or a top link included in the scope of delivery? No, only the tractor-side bracket is supplied. Translated with DeepL.com (free version)

for one-man operation, can also be used for coupling systems - working pressure 6-12 bar - includes a hose for suctioning liquids - dimensions: 225x135x192 mm (LxWxH).

enables a clean oil change by suction - suitable for engine, transmission and rear axle oils and other non-corrosive liquids - suction hose diameter in 9.8 - 8.0 - 6.7 - 4.5 mm for suction through the oil dipstick -Tube - 7.5 l container, with foot for a firm stand, for holding large amounts of oil - suitable for extracting oil from e.g. Smart but also for all other vehicles where an oil change needs to be carried out without using a lifting platform - with special silicone Brake bleeding hose with valve for one-handed operation - makes it easier to bleed brake systems on all vehicles - the built-in hand vacuum pump enables brake bleeding even without a compressed air connection.

Sheath 2300 mm long, 12 mm, rope 3800 mm long, 5 mm, incl. insert pocketReversible brake cable for vehicles up to a permissible total weight of 4000 kg, yellow chrome, tab cross section 51x10 mm.

Sheath 3500 mm long, 12 mm, rope 6200 mm long, 5 mm, including insert pocket, tab cross-section 51x10 mmReversible brake cable for vehicles up to a permissible total weight of 4000 kg, yellow chrome.

Sheath 2300 mm long, 12 mm, rope 5200 mm long, 5 mm, incl. insert pocketReversible brake cable for vehicles up to a permissible total weight of 4000 kg, yellow chrome, tab cross section 51x10 mm.

Galvanized cable pull, cable connection thread M8, sleeve length 1230 mm, cable length 1440 mm, bell outer dimension 22 mm

Mixture of white spirits and acetone free of chlorinated solvents short exposure time for cleaning brake systems, clutch parts, etc. removes oil, grease, wax and other deposits without leaving any residue ideal for use in the assembly and final treatment of workpieces, especially before painting applicable in the automotive industry, for removing brake dust or brake fluid also suitable for glass or ceramics.

Brake cleaner for cleaning brake systems, clutch parts, etc. Removes oil, grease, wax and other deposits without leaving any residue. With a very short exposure time, ideal for assembly and final treatment of workpieces, especially before painting. Can also be used in the automotive sector - to remove brake dust or brake fluid. Also suitable for glass or ceramics! Free from chlorinated solvents.

With 2 return springs. Single-acting, total length: 360 mm, stroke: 110 mm, piston rod 30 mm, connection: R3/8"~ IG.

With built-in return spring, installation length: 280 mm, stroke: 100 mm, cylinder inner 40 mm, connection: R1/4"~ Female thread, cylinder outer 50 mm, bolt 21 mm, fork slot 14.5x40 mm,

​Pull cylinder with built-in release spring, installation length centre-to-centre 405 mm, total length 430 mm, stroke: 85 mm, cylinder inner diameter 35 mm, cylinder outer diameter 45 mm, piston rod 25 mm, forks with 11 mm holes, connection: R 3/8"UF AG.

​For use with handbrake and footbrake  Width: 48 mmOuter diameter: ø 230 mmToothing: 44 x 48 Number of teeth: 23Reliable power transmission for handbrakes and footbrakes, precisely fitting brake drum for consistent braking performance. Outer diameter 230 mm, width 48 mm, pitch 44 x 48, 23 teeth. 

Original Steyr CNH spare part, ET no. 1-33-135-400, storage container,suitable for Steyr: Series 8000 SK1 and SK2 8060, 8070, 8080, 8090. Series 8100 SK1 and SK2: 8100, 8110, 8120, 8130. 900 series: 942, 948, 955, 964, 970, M948, M952, M958, M963, M968, M975. 9000 Series: 9078, 9086, 9094, M9078, M9083, M9086, M9094, 9080M, 9090M, 9100M. 9100 series: 9105, 9125, 9145. CVT series: 6140, 6150, 6160, 6175, 6195. suitable for case. CS Series: CS48, CS52, CS58, CS63, CS68, CS75

Suitable for all brake systems, miscible with any other brake fluid, boiling point above 260C, wet boiling point above 145C. 1L container.

For changing brake fluid quickly and easily. The 2-chamber system prevents the formation of air bubbles. Complete with 8-piece accessory set.

Steel flex, bright, external thread M10x1 that can be rotated on both sides with internal and external cones.

Brake hose for compressed air brake systems in motor vehicles and trailer vehicles. The compressed air hose is 100% pressure tested according to DIN 74310 and has a corded textile insert. The core and the top are made of black, smooth EPDM. The brake hose is very abrasion-resistant, resistant to aging and weather. Roll length 10m